Simultaneous Transmission Peak Location Separation Ratio Computational Workflow Protocols
SPLSR computational workflows extract 3D coordinates from SAR scans to verify that concurrent multi-radio emissions meet FCC exclusion limits below 0.04.

Trigger
Transmitter combinations in compact handheld and body-worn devices require exposure screening well before filing for commercial certification. Cellular transceivers housed alongside Wi-Fi 6E and Bluetooth chipsets emit RF fields that overlap within tissue. For portable equipment used within twenty centimeters of the body, regulatory authorities enforce strict absorption caps.
In the United States, the Federal Communications Commission limits specific absorption rate to 1.6 watts per kilogram averaged over one gram of tissue, and 4.0 watts per kilogram averaged over ten grams for extremities. If the mathematical sum of standalone 1-g SAR readings from concurrent transmitters stays under 1.6 watts per kilogram, the device qualifies for a test exclusion without geometric analysis. Exceeding that threshold rules out direct summation entirely.
Crossing that boundary forces secondary assessments. Tooling delays and board respins quickly run up thousands of dollars in engineering costs. The SAR-to-peak-location separation ratio, or SPLSR, serves as the main analytical filter to bypass full multi-transmitter volume SAR scans.
Under FCC KDB 447498, an SPLSR of 0.04 or less for 1-g body exposure allows compliance without full-volume phantom evaluations; for 10-g extremity limits, the ceiling sits at 0.10. Calculating this metric accurately requires exact spatial tracking across separate field distributions.
A summed specific absorption rate above 1.6 watts per kilogram forces spatial peak separation analysis across all active antenna pairs.
Silicon selection directly constrains antenna placement and concurrent transmission modes. Cellular basebands driving 5G New Radio bands n77 and n41 create absorption hotspots near bottom-edge feed lines, while high-throughput dual-band Wi-Fi radios running on 2.4 GHz and 5 GHz or 6 GHz channels register peaks along the top or side of the chassis. Architecture choices dictate whether the platform operates radios simultaneously or relies on time-division multiplexing to prevent overlap.
Once simultaneous transmission is fixed in hardware, spatial field coordinates determine market clearance.
Overlooking peak separation ratios early in board layout leaves little recourse later beyond throttling factory output power, which can cut wireless range in half.

Probe
Spatial measurements are performed using automated dosimetric systems equipped with isotropic electric-field probes scanning inside anthropomorphic phantoms. The shell contains dielectric liquid formulated to match the electrical properties of human muscle and brain tissue across defined frequency bands. A robotic arm moves miniature dipoles through a volumetric grid to map local field strength.
Grid spacing must be tight enough to capture the steep spatial gradients typical of mmWave and upper mid-band signals, as a coarse scan introduces interpolation errors that shift the registered peak coordinate.
Registration shifts between separate measurement sweeps invalidate downstream calculations. When evaluating an LTE band against a 5 GHz Wi-Fi link, the lab runs independent tests using band-specific tissue-simulating liquids. Each run establishes its own local coordinates anchored to reference marks on the phantom shell.
Shifting the device by even two millimeters during socket changes throws off the measured separation distance. Software scripts parsing post-processing exports must apply calibrated transformation matrices to map every field distribution to a common host coordinate system.
| Frequency Range (GHz) | Area Scan Grid Step (mm) | Zoom Scan Grid Step (dx, dy in mm) | Zoom Scan Vertical Step (dz in mm) | Minimum Zoom Volume (mm) |
|---|---|---|---|---|
| Below 3.0 | 15.0 | 8.0 | 5.0 | 30 x 30 x 30 |
| 3.0 to 4.0 | 12.0 | 5.0 | 4.0 | 28 x 28 x 28 |
| 4.0 to 5.0 | 12.0 | 4.0 | 3.0 | 25 x 25 x 22 |
| 5.0 to 6.0 | 10.0 | 4.0 | 2.0 | 22 x 22 x 22 |
| 6.0 to 7.125 | 8.0 | 3.4 | 1.4 | 22 x 22 x 22 |
Coordinate extraction isolates the precise point of maximum energy absorption by fitting higher-order polynomial surfaces to the raw zoom-scan cloud. Sharp dielectric contrasts near tissue boundaries frequently produce secondary local maxima. Peak-finding algorithms must isolate true radiated lobes from surface currents running along metallic ground structures, where trace noise can introduce phantom peaks that skew distance figures.
Antenna coupling shifts the apparent peak coordinate when both radiators operate in close proximity.

Geometry
Evaluating the separation ratio depends on the straight-line Euclidean distance between peak absorption coordinates. The primary transmitter registers its maximum spatial peak SAR, denoted as SAR1, at coordinates (x1, y1, z1). The secondary concurrent transmitter registers SAR2 at (x2, y2, z2).
The spatial separation distance, Ri, represents the physical span between these points in millimeters. The ratio divides the summed absorption values raised to the 1.5 power by this separation distance.
SPLSR is calculated as (SAR1 + SAR2)^1.5 divided by Ri, where coordinates are in millimeters and absorption values are in watts per kilogram. When multi-antenna arrays generate distributed hotspots across the device, every active pair requires individual evaluation. For an enterprise terminal carrying cellular, dual-band Wi-Fi, and Bluetooth radios, post-processing tools must evaluate every active combination across each certified test position.
Physical separation begins with board layout. Several design variables determine whether spatial distance can offset higher conducted powers:
- Antenna feed displacement sets the baseline physical gap between distinct radiating structures along the main printed circuit board chassis edges.
- Ground plane geometry alters current distribution paths, dragging apparent absorption centroids away from the physical antenna feed points toward common chassis return paths.
- Chassis shielding cans suppress parasitic surface currents that otherwise form phantom secondary peaks across digital signal processing partitions.
- Dielectric casing thickness controls the direct standoff distance between antenna radiating traces and the external phantom surface contact plane.
Take a concrete layout: an industrial handheld with an LTE Band 7 radio operating at 2.5 GHz alongside a 5.8 GHz Wi-Fi link. Calibrated conducted power yields a standalone 1-g absorption of 1.15 watts per kilogram for LTE at (12.4, 45.2, -8.1). The Wi-Fi radio measures 0.92 watts per kilogram at (14.1, -38.6, -7.5).
Summed directly, the values reach 2.07 watts per kilogram, surpassing the 1.6 watts per kilogram threshold and requiring peak separation analysis.
The calculation resolves through deterministic steps:
- Spatial difference along the x axis equals 14.1 minus 12.4, yielding 1.7 millimeters.
- Spatial difference along the y axis equals -38.6 minus 45.2, yielding -83.8 millimeters.
- Spatial difference along the z axis equals -7.5 minus -8.1, yielding 0.6 millimeters.
- Summing the squared deviations yields 2.89 plus 7022.44 plus 0.36, totaling 7025.69 square millimeters.
- Taking the square root yields a three-dimensional distance Ri of 83.82 millimeters.
- Summing SAR1 and SAR2 produces 2.07 watts per kilogram.
- Raising 2.07 to the 1.5 power yields 2.978.
- Dividing 2.978 by the separation distance of 83.82 millimeters yields an SPLSR of 0.0355.
Because 0.0355 sits below the 0.04 regulatory ceiling, the design qualifies for the exclusion without multi-transmitter volumetric scans. Had the physical separation dropped to 70.0 millimeters at those same power levels, the ratio would reach 0.0425, failing the exemption criteria.
| SAR1 (W/kg) | SAR2 (W/kg) | Summed SAR (W/kg) | Distance Ri (mm) | Calculated SPLSR | Compliance Status (1-g Limit 0.04) |
|---|---|---|---|---|---|
| 0.85 | 0.82 | 1.67 | 45.0 | 0.0479 | Non-Compliant Exclusion Failed |
| 0.85 | 0.82 | 1.67 | 55.0 | 0.0392 | Compliant Exclusion Granted |
| 1.20 | 0.95 | 2.15 | 60.0 | 0.0525 | Non-Compliant Exclusion Failed |
| 1.20 | 0.95 | 2.15 | 80.0 | 0.0394 | Compliant Exclusion Granted |
| 1.45 | 1.10 | 2.55 | 95.0 | 0.0428 | Non-Compliant Exclusion Failed |
| 1.45 | 1.10 | 2.55 | 105.0 | 0.0388 | Compliant Exclusion Granted |
Spatial separation values maintain stability only when antenna ground returns remain completely decoupled across the entire radio frequency board area.

Run
Automated extraction pipelines remove the manual entry errors common between dosimetric scan exports and final compliance tables. Test suites generate thousands of pages of raw SAR data across channel plans, modulation types, and device orientations. Custom parsing scripts read these native files directly, isolate volumetric centroids, and compute Euclidean distances across every active co-transmission scenario, immediately flagging combinations that breach the exclusion cap.
Dynamic power back-off routines in firmware tie straight into these figures. When onboard capacitive proximity sensors detect contact with skin, the processor throttles baseband amplifier drive. Backing off power by three decibels cuts radiated power in half, scaling down localized SAR accordingly.
Analysis scripts check whether programmed attenuation keeps simultaneous emissions compliant across every supported mode without dropping active cellular links.
Under FCC KDB 447498 D04 Section 4.3.2, simultaneous transmission exclusion requires documented peak separation ratios across all concurrent operating modes.
Shared radiators present distinct complications for automated pipelines. An antenna covering both 850 MHz and 1.8 GHz shifts its spatial absorption peak based on hand loading and instantaneous tuning. If a 2.4 GHz Wi-Fi antenna sits nearby, the separation distance Ri can drift by fifteen millimeters purely from band switching.
The analysis pipeline cannot model the dual-band element as a fixed point in space; it has to track peak coordinates separately for each operational state.
Verification routines require regular calibration against physical reference dipoles positioned over flat phantoms. Automated extraction scripts run against these baseline data sets must confirm centroid locations to within 0.1 millimeters. Sourcing teams reviewing supplier qualification files inspect these reference runs to ensure post-processing scripts have not been modified or misconfigured.
How do rapid structural dielectric variations across miniaturized housings influence localized coordinate shift when human hands compress external antennas during actual operation?

Clearance
Regulatory approval governs commercial release in every target market. Once simultaneous transmission metrics pass, test laboratories assemble the compliance documentation submitted to Telecommunication Certification Bodies, which regional authorities review prior to granting market access. Sourcing contracts routinely require original design manufacturers to furnish detailed matrices documenting raw SAR values, spatial coordinates, and separation ratios across all supported operating conditions.
Carrier board integration requires strict adherence to module clearance rules. If an approved radio module specifies a five-millimeter buffer to adjacent radiators, host integrators must maintain that spacing; encroaching on it voids the modular grant and forces full host-level SAR testing at the brand’s expense. Supply agreements address this by allocating recertification costs directly to the ODM if board revisions alter validated antenna clearances.
Section 8.2 of the master supply agreement specifies that any design change shifting radio peak coordinates beyond two millimeters triggers immediate sample recertification at the supplier expense.
